[Interface de communication]：RS485
[Distance de transmission]：5 km
[Tension de fonctionnement]：DC 8-28 V
[Méthode d'installation]：Rail DIN
[Dimensions]：113 x 107 x 65 mm
[Poids]：189 ± 5 g
[Introduction]：Le commutateur d'intercommunication sans fil est un terminal utilisant la technologie de modulation LoRa pour la transmission sans fil à distance des valeurs de commutation. Il prend en charge 8 entrées de commutation d'acquisition (DI) et 8 sorties relais de contrôle (DO). Fonctionnant dans la bande de fréquences 850,125-930,125 MHz, sa fonction principale est la commande synchrone à distance. Aucun câblage n'est requis et sa grande convivialité permet aux utilisateurs de l'intégrer rapidement à leurs propres systèmes. Il accepte une tension d'entrée continue de 8 à 28 V. Il est recouvert d'un revêtement conforme résistant à la moisissure, à l'humidité et au brouillard salin.
Magasin officiel
| Pin | Device Port Description |
| 1 | Switch input port 1 |
| 2 | Switch input port 2 |
| 3 | Switch input port 3 |
| 4 | Switch input port 4 |
| 5 | Switch common terminal |
| 6 | Switch input port 5 |
| 7 | Switch input port 6 |
| 8 | Switch input port 7 |
| 9 | Switch input port 8 |
| 10 | Switch common terminal |
| 11 | GND |
| 12 | RS485-A |
| 13 | RS485-B |
| 14 | PE (protective earth) |
| 15 | DC 8～28V(V-) |
| 16 | DC 8～28V(V+) |
| 17 | Relay output normally open port 1 |
| 18 | Relay output COM port 1 |
| 19 | Relay output normally open port 2 |
| 20 | Relay output COM port 2 |
| 21 | Relay output normally open port 3 |
| 22 | Relay output COM port 3 |
| 23 | Relay output normally open port 4 |
| 24 | Relay output COM port 4 |
| 25 | Relay output normally open port 5 |
| 26 | Relay output COM port 5 |
| 27 | Relay output normally open port 6 |
| 28 | Relay output COM port 6 |
| 29 | Relay output normally open port 7 |
| 30 | Relay output COM port 7 |
| 31 | Relay output normally open port 8 |
| 32 | Relay output COM port 8 |
| 33 | STATE configuration reset button |
LED indicator and button description
| port | LED indicator color | illustrate |
| PWR | Blue LED | Power indicator light, always on when powered on, off when no power |
| LINK | Yellow LED | 1 to many (including 1 to 1) - bidirectional (when the devices have the same number of channels): |
| l As long as one slave is successfully connected to the master, the LINK indicator of the master will be on; | ||
| After the slave device is successfully connected to the host device, the LINK indicator of the slave device will be on; | ||
| 1 to many - two-way (different number of channels, each channel of the host is independently controlled by the slave): the host LINK indicator flashes several times according to the number of devices connected (cycle 300ms, after flashing, it goes out for 1s, and then flashes again). For example: if 3 devices are connected, the LINK indicator flashes 3 times according to the cycle, then goes out for 1s and flashes again; | ||
| STATE (indicator light) | Blue LED | Host: The indicator light is always on; |
| Slave: indicator light flashes slowly; | ||
| Pairing: indicator light flashes quickly; | ||
| Not paired: the indicator light is off; | ||
| STATE (button) | White buttons | 1. Press and hold for 2 seconds to enter pairing mode; |
| 2. Press and hold for more than 6 seconds to restore to factory settings; | ||
| 3. Press and hold to cycle through the pairing state and reset state; | ||
| 5. In pairing mode, short press to exit pairing mode | ||
| DI1-DI8 | Green LED | Device switch input data indication, normally on means there is input, normally closed means there is no input |
| DO1-DO8 | Red LED | Each of the 8 relay output switch indicators corresponds to the 8 relay outputs; normally on indicates output is in progress, and normally closed indicates no output. |