E180-Z5812SP Ebyte OEM/ODM 11dBm JN5189 500m petite taille faible consommation d'énergie haute fiabilité bande 2.4GHz Module ZIGBEE
[Poids du produit]：0.9g
[IC]：TLSR8258
[La fréquence]：2.40~2.48GHz
[Du pouvoir]：12dBm
[Distance]：200m
[Taille]：11.5*22mm
[Introduction]：E180-Z5812SP est un module ZigBee basé sur le SoC sans fil TELINK TLSR8258 conçu et produit par Ebyte, qui est de petite taille, faible consommation d'énergie, haute fiabilité et fonctionne dans la bande de fréquence 2,4 GHz. La puce dispose d'un microcontrôleur hautes performances 32 bits jusqu'à 48 MHz, avec une puissance de transmission maximale de 12 dBm et un courant de veille minimal de 2 uA.
Magasin officiel
| Pin number | Pin name | Pin direction | Pin usage |
| 1 | NC | - | Reserved, directly suspende |
| 2 | GND | - | Ground wire, connected to power reference ground |
| 3 | NC | - | Reserved, directly suspende |
| 4 | PD3(WAKE) | Input | The WAKE pin is mainly used to wake up the dormant terminal. It is at a high level when powered on. When the pin is pulled low externally, the |
| 5 | PD7(TX) | Output | Serial sending port TX |
| 6 | PA0(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, directly suspended |
| 8 | NC | - | Reserved, directly suspended |
| 9 | PD4(MODE) | Input | Working mode switching pin, when the pull-down time is greater than 500ms, the working mode is switched. |
| 10 | PA1(BAUD_R) | Input | The UART_BAUD_RESET pin is used to reset the baud rate of the device. It defaults to a high level when powered on. In any mode, if the pin is pulled down for more than 1000ms, the serial port parameters of the module will restore the default 11520 |
| 11 | PB1(ACK) | Output | The ACK pin is used to indicate the status of the last user datatransmission. The pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful |
| 12 | PC0(GPI00) | Input/Output | GPIO input/output port 0 |
| 13 | VCC | - | Module power positive reference voltage, voltage range |
| 14 | GND | - | Ground wire, connected to power reference ground |
| 15 | PB4(GPI01) | Input/Output | GPIO input/output port 1 |
| 16 | NC | - | Reserved, directly suspended |
| 17 | NC | - | Reserved, directly suspended |
| 18 | PB5(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and when it is high, it indicates that the device is idle |
| 19 | NC | - | Reserved, directly suspended |
| 20 | NC | - | Reserved, directly suspended |
| 21 | PB6(ADC1) | Input | ADC detection port 1 |
| 22 | PB7(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | SWCLK | Input/Output | Serial debug interface, serial line clock |
| 26 | SWDIO | Input/Output | Serial debugging interface, serial data input and output |
| 27 | PC2(PWM0) | Output | PWM output port 0 |
| 28 | PC3(PWM2) | Output | PWM output port 2 |
| 29 | PC4(PWM3) | Output | PWM output port 3 |
| 30 | PC1(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high level meter has joined the network |
| 31 | NC | - | Reserved, directly suspended |
| 32 | PD2(PWM1) | Output | PWM output port 1 |
| 33 | NC | - | Reserved, directly suspended |
| 34 | NC | - | Reserved, directly suspended |
| 35 | NC | - | Reserved, directly suspended |
| 36 | GND | Input/Output | Ground wire, connected to power reference ground |
| 37 | nRESET | Input | Reset pin |