E18-MS1-PCB_CC2530_Zigbee_Module

Home >Module>Zigbee>CC2530

E18-MS1-PCB Module Ebyte ZigBee RF CC2530, réseau d'animation pour maison intelligente, OEM E18-MS1-PCB, Solution IOT

[IC]：CC2530

[La fréquence]：2.4~2.48GHz

[Du pouvoir]：4dBm

[Distance]：0.2km

[Interface]：UART/IO

[Poids du produit]：1.2±0.1g

[Introduction]：E18-MS1-PCB est basé sur la puce RF CC2530 originale importée de forme TI en Amérique. La puce IC est intégrée au microcontrôleur 8051 et à l'émetteur-récepteur sans fil à l'intérieur, ce qui s'applique à la conception Zigbee et au protocole 2,4 GHz IEEE 802.15.4. Tous les ports IO sont dirigés par le module, ce qui signifie que le développement multi-aspects est réalisable.

Send Inquiry

Purchase

Téléchargements de fichiers Compare

Pin number	CC2530 Pin name	Module Pin name	Input/Output	Pin usage
1	GND	GND		Ground wire, connected to the power reference ground
2	VCC	VCC		Power supply, must be between 1.8' 3. 6V
3	P2.2	GPIO	I/O	DC-download program or Debug clock interface
4	P2. 1	GPIO	I/O	DD-download program or Debug data interface
5	P2.0	GPIO	I/O	N/C
6	Pl. 7	NWK_KEY	I	Used for manual join, exit, and quick match keys. Not networked: Short press to join the network or create a network operation; Networked: Short press for quick match; Long press means to leave the current network; Note: Low level is valid, 100ms W short press W 3000ms, 5000 W long press.
7	PL 6	GPIO	I/O	N/C
8	NC	NC		N/C
9	NC	NC		N/C
10	Pl. 5	UARTO.TX	O	Serial port TX pin
11	Pl. 4	UART0_RX	I	Serial port RX pin
12	Pl. 3	RUN_LED	O	It is used to indicate the network access status of the module. Fast flashing 256 times (10Hz frequency) indicates that it is joining the network or creating a network, and slow flashing 12 times (2Hz frequency) indicates that the module has joined the network or successfully created the network; Low level lights up;
13	Pl. 2	NWK_LED	O	It is used to indicate the one key pairing status of the module, provided that two modules need to join the same coordinator, and then one key pairing can be performed. In the transparent mode, mutual transparent transmission can be performed. Low level lighting;
14	Pl. 1	GPIO	I/O	The PA transmit control pin has been connected inside the module; There is no PA inside the E18-MS1-PCB/E18-MS1-IPX;
15	P1.0	GPIO	I/O	The PA receiving control pin has been connected inside the module; There is no PA inside the E18-MS1-PCB/E18-MS1-IPX;
16	P0.7	HGM	O	HGM pin of PA; E18-MS1-PCB/E18-MS1-IPX has no PA inside, so this pin is used as GPIO port;
17	P0.6	GPIO	I/O	N/C
18	PO. 5	GPIO	I/O	N/C
19	P0.4	GPIO	I/O	N/C
20	P0.3	GPIO	I/O	N/C
21	P0.2	GPIO	I/O	N/C
22	PO. 1	GPIO	I/O	N/C
23	PO.O	GPIO	I/O	N/C
24	RESET	RESET	I	Reset port

